AUTOSLOT Auto Stop for Pachislo Skill Stop Slot Machines
The AUTOSLOT Auto Stop enables your Pachislo Skill Stop machine to perform more like traditional Las Vegas slot machines.
After inserting credits, and pressing the Start/Spin lever, the Auto Stop will automatically stop the reels.
No longer any need to press the stop buttons!
What are the features of the AUTOSLOT Auto Stop?
We believe the AUTOSLOT Auto Stop is the best value of any unit currently on the market!
Our unit fits practically every Pachislo machine made in the last 15 years!
Simple Installation, No soldering! Simply replace one cable with the AUTOSLOT Auto Stop cable.
All settings adjustable by using the 3 existing reel stop buttons on your machine.
You can select Auto Stop mode ON or OFF.
The order in which the reels stop is selectable between traditional left to right order, or random order.
You can control both how long until the reels begin to stop* and how much time between each reel stop.
All
settings are retained after machine is turned off! No need to
select each setting every time the slot machine is powered up.
(Ask the competitors if theirs does this!)
Includes label with function summary.
How do I change the settings?
(Note: buttons must be held down for 2 or more seconds.)
Refer to the chart below. To turn ON the Auto Stop mode, press down the left reel stop button while the reels are stopped. To turn it OFF, simply press down the left button again.
Normally, the reels will stop in a Left to Right order. To have the reels stop in a Random order, press down the center button. The microcontroller uses a Random Number generator to change the stop order on each spin. Press down the center button again to switch back to Left to Right.
Once the spin lever is pushed, the default time that all the reels spin before the first one stops is 2 seconds. You can adjust this Spin-Stop Delay time from a minimum of 1 second to a maximum of 3 seconds. To Decrease the Spin-Stop Delay by ½ second, press down the left and center buttons at the same time. To Increase the Spin-Stop Delay by ½ second, press down the center and right buttons at the same time. Repeat as needed.
The default time between one reel stopping and the next is ½ second. This Reel-Reel Delay time can be changed to 1 second by pressing down the left and right buttons at the same time. Press down these buttons again to switch the machine back to ½ second delay.
You can Restore the Default settings (Auto Stop On; Random Off; 2 sec Spin-Stop Delay; 1 second Reel-Reel Stop Delay) by pressing down all three buttons at the same time.
BUTTON STATUS |
FUNCTION when button(s) held for over 2 seconds |
||
● |
|
|
Toggle Auto Stop Mode On/Off |
|
● |
|
Toggle Random Mode On/Off |
● |
● |
|
Decrease Spin-Stop Delay by ½ sec |
|
● |
● |
Increase Spin-Stop Delay by ½ sec |
● |
|
● |
Toggle Reel-Reel Delay between ½ and 1 sec |
● |
● |
● |
Restore Defaults |
How does it work?
The AUTOSLOT uses a state-of-the-art microcontroller to control the machine’s stop function. It uses the machine’s reel stop buttons as inputs. By pressing down the buttons for 2 or more seconds, you tell the microcontroller how you want the machine to stop the reels. The microcontroller stores these settings in EEPROM memory, that will retain the settings for up to 40 years with the power off! No battery backup needed. You can change the settings any time you want.
How will I know if this will work in my machine?
Open the front door and locate the stop board in your machine. (Location varies, but the stop board is usually located towards the back right of your machine.)
|
If your board looks like one of these two pictured below, then no problem!
However, if your stop board looks like this next picture, then you have an OLD machine,
and the AUTOSLOT WILL NOT WORK!
Also starting in 2004 Pachislo's were upgraded which removed these Traditional 30 Pin Stop Boards. If you have a 2004 or newer Pachislo and have the Newer Stop Boards shown Below the Standard AutoSlot will not work. The AS-06 will be required and must be wired directly into the wiring of the inner door PC Board.
How do I install it?
Unplug machine from the outlet. Open the machine door. Locate the stop board and remove the 30 conductor cable by pressing down on the two cable release levers. (Do not disconnect the other end of the cable from the motherboard). Plug the end of your existing cable into the AUTOSLOT Auto Stop cable and the other end of the AUTOSLOT Auto Stop cable into the connector on your stop board, making sure the levers latch back into place. Close the door, turn on the power and you are ready to go!
*Note: The AUTOSLOT Auto Stop is designed to work with the majority of current model Pachislo machines. However, there are a few models that use non-standard wiring. On these models the Auto Stop function still works, but you lose the ability to adjust the Spin-Stop delay.